Manual: foo2hbpl2-wrapper
foo2hbpl2-wrapper(1) General Commands Manual foo2hbpl2-wrapper(1)
NAME
foo2hbpl2-wrapper - Convert Postscript into a ZJS printer stream
SYNOPSIS
foo2hbpl2-wrapper [options] [ps-file]
DESCRIPTION
foo2hbpl2-wrapper is a Foomatic compatible printer wrapper for the foo2hbpl2 printer driver. This script reads a
Postscript ps-file or standard input and converts it to Zenographics ZjStream printer format for driving the Dell
1355, Dell C1765, Epson AcuLaser M1400, Epson AcuLaser CX17NF, Fuji Xerox DocuPrint CM205, Fuji Xerox DocuPrint
CM215, Fuji Xerox DocuPrint P205, Xerox Phaser 3010, Xerox Phaser 3040, Xerox WorkCentre 3045 MFP, and Xerox WorkCen‐
tre 6015 MFP printers.
This script can be used in a standalone fashion, but is intended to be called from a printer spooler system which
uses the Foomatic printer database.
COMMAND LINE OPTIONS
Normal Options
These are the options used to select the parameters of a print job that are usually controlled on a per job basis.
-c Print in color (else monochrome).
-C colormode
Color correction mode [0].
10 ICM color profile (using -G *.icm file)
-d duplex
Duplex code to send to printer [1].
│ │ │
│ 1 off │ 2 long edge │ 3 short edge
-m media
Media code to send to printer [1].
─────────────────
Media HBPL
─────────────────
plain 1
bond 2
lwcard 3
lwgcard 4
labels 5
envelope 6
recycled 7
plain2 8
bond2 9
lwcard2 10
lwgcard2 11
recycled2 12
-p paper
Paper size code to send to printer [1].
────────────────────────────
Paper HBPL
────────────────────────────
A4 1
B5jis 2
A5 3
letter 4
executive 5
fanfold german legal 6
folio 6
legal 7
env#10 9
envMonarch 10
envC5 11
envDL 12
-n copies
Number of copies [1].
-r xresxyres
Set device resolution in pixels/inch [1200x600].
-s source
Source (Input Slot) code to send to printer [7].
│ │
│ 1 upper │ 4 manual
│ 2 lower │ 7 auto
-t Draft mode. Every other pixel is white.
-T density
Print density (1-5). The default is 3 (medium).
-2 -3 -4 -5 -6 -8 -9 -10 -12 -14 -15 -16 -18
Print in N-up. Requires the psutils package.
-o orient
Orientation used for N-up.
Portrait -op (normal)
Landscape -ol (rotated 90 degrees anticlockwise)
Seascape -os (rotated 90 degrees clockwise)
Printer Tweaking Options
These are the options used to customize the operation of foo2hbpl2 for a particular printer.
-u xoffxyoff
Set the offset of the start of the printable region from the upper left corner, in pixels [varies with paper
size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on any other printers.
-l xoffxyoff
Set the offset of the end of the printable region from the lower right corner, in pixels [varies with paper
size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on any other printers.
-L mask
Send the logical clipping values from -u/-l in the ZjStream. foo2hbpl2-wrapper always runs Ghostscript with
the ideal page dimensions, so that the scale of the image is correct, regardless whether or not the printer
has unprintable regions. This option is used to move the position of the clipped image back to where it be‐
longs on the page. The default is to send the amount which was clipped by -u and -l, and should be good in
most cases.
0 don't send any logical clipping amounts
1 only send Y clipping amount
2 only send X clipping amount
3 send both X and Y clipping amounts
-P Do not send START_PLANE codes on monochrome output. May be needed by some monochrome-only printers, such as
the HP LaserJet 1000.
-X padlen
Add extra zero padding to the end of BID segments. The default is 16 bytes. Padding 16 bytes of zeroes is
needed for older ZjStream printers, such as the Minolta 2200DL and HP LaserJet 1000, and seems harmless to
newer ones, such as the Minolta 2300DL. So the default should be good for all cases.
Color Tweaking Options
These are the options used to control the quality of color output. Color correction is currently a WORK IN PROGRESS.
-g gsopts
Additional options to pass to Ghostscript, such as -g“-dDITHERPPI=nnn”, etc. This option may appear more than
once.
-G profile.icm
Convert profile.icm to a Postscript color rendering dictionary (CRD) using foo2zjs-icc2ps and adjust the
printer colors by using the Postscript setcolorrendering operator. (WORK IN PROGRESS).
-G gamma-file.ps
Prepend gamma-file.ps to the Postscript input to perform color correction using the setcolortransfer Post‐
script operator. For example, the file might contain:
{0.333 exp} {0.333 exp} {0.333 exp} {0.333 exp} setcolortransfer
-I intent
Select profile intent from the ICM file. 0=Perceptual, 1=Colorimetric, 2=Saturation, 3=Absolute. Default is
0 (perceptual).
Debugging Options
These options are used for debugging foo2hbpl2 and its wrapper.
-S plane
Output just a single color plane from a color print and print it on the black plane. The default is to output
all color planes.
1 Cyan
2 Magenta
3 Yellow
4 Black
-D level
Set Debug level [0].
EXAMPLES
Create a monochrome ZjStream from a Postscript document, examine it, and then print it using a RAW print queue:
foo2hbpl2-wrapper testpage.ps > testpage.prn
hbpl2decode < testpage.prn
lpr -P raw testpage.prn
Create a color ZjStream stream from a Postscript document:
foo2hbpl2-wrapper -c testpage.ps > testpage.prn
FILES
/usr/bin/foo2hbpl2-wrapper
SEE ALSO
foo2hbpl2(1), hbpldecode(1)
AUTHOR
Rick Richardson
http://foo2hbpl.rkkda.com/